What do i know about 48000hz versus 44100hz? I don't know - I will switch back and forth until I find out!Ĥ4100 for studio stuff, since that's default. Then go to the playback and do the same thing for the speakers, select 48000hz, and it will warn you that a program might stop working, but as long as you PUT UAD CONSOLE TO 48000HZ FIRST, ITS OKAY (I read this on UAD website). Now, go over to that menu you led me where "listen to this device" is. Thank you for that.įirst, go to UAD Console and set it to 48000Hz in settings. Because, I did what you said, and it was true. You might have just led me to the solution. It seems to be less bad the higher you go up! This makes the problem not so bad, but when I set it to UA Apollo Thunderbolt, it gets much more worse (for recording or for playing sounds off FlStudio)! I uploaded that here: - I also tried uninstalling ASIO4ALL driver that came with FL Studio and reinstalling Apollo's drivers.ĮDIT: Nevermind, it only worked for a bit out of luck, and seemed like it only slightly helped, lol. When I am on FL Studio, and I set the sample rate and buffer lengths to match, I also picked my input/output device to be FL Studio ASIO. The static/distortion seems connected to the wiring when I physically touch them - but the wires are FINE when I'm using the UAD Console or the Apollo Twin itself! I uploaded it here: - oh, and I can't even play any of my sounds with FL Studio through the Apollo without this distortion as well! But Spotify and Discord work fine! However, when I try recording on FL Studio, or using Skype, Discord, Vocaroo, whatever, there is a big static/distortion. the green tracker which shows you how far long in the song you are during playback moves incredibly slowly) and through the earphones (plugged into the TASCAM) I can hear the odd micro-second of clipped audio - every couple of seconds.So, when I'm using the Apollo Twin MK2 Duo's talkback or direct-monitoring feature, I pick up my connected microphone fine and with crisp, clear vocals. Result: The song immediately appears to start buffering (i.e. In Device -> If I chose ASIO devices: I chose "US-122L / US-144"Ĭlick on "Show ASIO panel" -> Settings are as follows: (ii) Try to listen to FL Studio song/pattern via TASCAM US-144 interface (w/ headphones) I can hear the song playing clearly & smoothly via the PC (or headphones plugged into PC). (i) Try to listen to FL Studio song/pattern via computer speakersįor "Device" I chose any of these options ("Primary Sounds Driver" or "Speaker/Headphones" or "ASIO4ALL v2") While the Tascam interface is connected I tried the following: Then, you’ll want to increase the buffer length. Once the window pops up, you’ll need to set your device to ASIO4ALL or FL Studio ASIO. Start by going up to options > audio settings. I want to solve this problem before I even begin trying to grapple with using the TASCAM audio interface to record a track Increasing the buffer length within the audio settings menu is the typical fix for any problems with choppy audio. There are a few other switchable options in the audio. Try and set the sample rate to 44100 Hz and the Priority to highest. You can increase the buffer length to where it works best for you. Problem: Even before I attempt to record anything I am unable to successfully listen to a song/pattern in FL Studio via the headphones I've plugged into the Tascam audio interface. For this, you’ll need to go to Options, Audio Setting, and then select the Asio4ALL or FL Studio Asio in the Device menu. System Type: 64-bit operating system, 圆4-based processor Processor: Intel(R) Core(TM) i7-8750H CPU 2.20GHz Now go to Show ASIO Panel, then ASIO properties, and finally click on the ASIO4ALL driver dialog box. There you can choose ASIO4ALL v2 in the Output dialog box and then open the driver settings. ASIO drivers because ASIO4ALL is at best rickety) on Windows. Then go to the Settings window and open the Audio options. I love FL Studio because it doesnt have a limit on number of installations. Software: FL Studio Producer Edition v20.0.1 To run ASIO in FL Studio you must open the DAW and press F10. Goal: I'm trying to connect the Tascam US -144 audio interface to my computer in order to record guitar/vocals in FL Studio
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |